Nonetheless it starts with something good and not mucking it up but instead solidifying any "looseness" anywhere behind the cartridge inside the chamber, and allowing the barrel in front of it to "free float" with no contact on the stock, anywhere. That's what I've read, anyway, and it makes sense: lock the cartridge and bullet inside the chamber like an iron glove and, upon firing it, have nothing interfere with the flight of the bullet down the barrel. So I chose a Remington 700 action and barrel in .280 that I've had in another less functional stock for thirty years, a sporter 22" barrel and no super 26" Howitzer launcher just yet, but one with which I've managed to drop an antelope at a guide-estimated 600-700 yards in its previous incarnation and know it to be consistent, which is what this whole game is about in the first place: know exactly where your bullet is at ALL times, from box to flight to zero velocity, dead-stop downrange. To do this, it's necessary to memorize the ballistic chart of the bullet you're shooting. There really is no substitute for that and it is proven when one misses a shot by an inch or whatever distance for no other reason than what was printed in black on white right there, on the chart.
I'm still working on that myself but it's true.
Here's a shot of the rifle in mid-metamorphosis in her Bell and Carlson Mountain synthetic stock of Kevlar and fiberglass and other non-warpable things, after a lot of shaping and tinkering, just to get a feel for things coming together...
After holding a standard Remington synthetic stock, which I liked, I wanted something with a different texture and I definitely wanted Aluminum Pillars in the stock to connect to the receiver or an entire bed of aluminum, for both solidity and stability, that one-piece unit feel. The Bell and Carlson had these pillars already installed, and after browsing and selecting, Midway zipped one out to me within a week. All that was needed was a little sanding to get everything to meet up smoothly and tightly for a custom fit, and a lot of sanding on the barrel channel to allow for a free float of the heavier Sporter barrel I have (the B and C stock was currently only available for the skinnier, "lightweight" barrel and I was not feeling patient that day, I can tell you--I was hot to get on this project). This is simply a good feeling stock. And it would feel even better, soon, after I further customized her to my rifle's action and barrel...
Onward to the real adventure of potential disaster, the "Glass Bedding" of the stock, to form-fit the stock to the whole gun, specifically the receiver and barrel chamber areas, and all the way back down along to the tail of her, the "tang" area, where the back-most screw tightens things together.
The most important area, I've been told, is the receiver and chamber area, where solidity is paramount. Here it is, after I've done the epoxy treatment for a form-fit, using Miles Gilbert Bedrock, also from Midway (it took me three epoxy application sessions to get it really smooth back-to-front, as it was my very first time to try this and I went cautious).
On first handling this "Bell and Carlson Mountain Stock with Aluminum pillars and Lightweight barrel channel, black", and checking her for compatibility, everything fit fairly snugly except for the thick, sporter barrel, which of course rode a little high, but she would have bolted right in and a lazier man would've stopped with that and probably have been satisfied.
The only digging and routing necessary was for the barrel channel. The stock's shallow channel for the "lightweight" Remington 700 barrel was not nearly deep enough to allow a free-float of my Sporter 22" barrel, a rather stout barrel. So I first tried sandpaper......it worked, but way too slowly, so......to Amazon we go, looking under "Dremel Moto-tool". A week later the Dremel 4000 created a new, deep barrel channel for my Remy inside of ten minutes. The Kevlar and fiberglass was nothing to shave away for this beast. I find myself looking for other projects to tear up with this thing.
There was maybe 1/16-1/8" of airspace around the receiver sides and after sanding a lot of airspace in front of the barrel stop lug. Not good enough.....So, I watched the "Glass bedding a rifle stock" video on Midway's Video Library and was struck with the mission. I would not be stopped. I should have been. I learned the importance of black, electrician's tape a little late, but the patient survived. Critically, line the stock's edges all around whereever you intend to epoxy, and whereever you do not wish to epoxy, and you will do fine. Also, APPLY PLENTY OF THE INCLUDED 'RELEASE' COMPOUND TO ALL EXPOSED AREAS OF THE BARREL AND RECEIVER THAT WILL EVEN POSSIBLY COME INTO CONTACT WITH THE GLASS EPOXY . Enough of that all-caps scary stuff. On to part II.